
Description
Factor X Polyclonal Antibody – Affinity Purified – Sheep
Affinity’s Factor X Polyclonal Antibody – Affinity Purified – Sheep is the highest level of our Factor X antibody family. During the Antigen Affinity Purification process the IgG has had any non-specific immunoglobulin fraction eliminated which enriches the specificity of the remaining immunoglobulin towards the target antigen. The result is a very high-purity product with a substantially higher titre than whole or purified IgG. Our Factor X Polyclonal Antibody – Affinity Purified – Sheep is provided in a solution of HEPES buffered saline containing 50% glycerol (v/v) and is intended for applications such as immunoblotting, immunostaining of cells and several types of immunoassays where the higher signal-to-noise ratio achieved with this enriched product is required.
Product Code: SAFX-AP
Retail Product Size: 0.5mg vial
Host Animal: Sheep Anti-Human Factor X Polyclonal Antibody – Affinity Purified
Species Cross Reactivity: View Chart
Product Datasheet: Factor X F10 Polyclonal Antibody, affinity purified anti-human sheep IgG
Description of Factor X (FX)
Factor X (FX, Stuart Factor) is a vitamin K-dependent glycoprotein produced in the liver. The concentration of FX in plasma is ~10 μg/ml (~170 nM). Factor X is expressed as a two-chain molecule with a molecular weight of 59 kDa. The light chain (17 kDa) of FX contains a calcium-binding domain consisting of one hydroxy-aspartic acid and 11 γ-carboxyglutamic acid (gla) residues. These residues allow F.X to bind to membranes that contain acidic phospholipids in a calcium dependent manner. This is followed by two EGF-like domains. The heavy chain of FX (42 kDa) consists of the catalytic domain, carbohydrate and the activation peptide. Activation of FX to the active enzyme (FXa) results from cleavage at residue Arg52 in the heavy chain of F.X by a complex of F.IXa, cofactor VIIIa, calcium and negatively charged phospholipid surface (the tenase complex), or by the F.VIIa-tissue factor complex. Both activation pathways result in the release of the activation peptide from the N-terminal of the heavy chain. The FXa generated is a serine protease responsible for the activation of prothrombin to thrombin in the presence of a phospholipid membrane, calcium and cofactor Va. The activity of FXa in plasma is inhibited by antithrombin (ATIII), α1antitrypsin, α2macroglobulin and tissue factor pathway inhibitor (TFPI). The inhibitory activity of ATIII is stimulated approximately 1000-fold by heparin1-3.
References and Review
- Ichinose A, Davie EW; The Blood Coagulation Factors: Their cDNAs, Genes, and Expression; in Hemostasis and Thrombosis, 3rd Edition, eds. RW Colman, J Hirsh, VJ Marder and EW Salzman, pp 19-54, J.B. Lippincott Co., Philadelphia PA, USA, 1994.
- Steinberg M, Nemerson Y; The Activation of Factor X; in Hemostasis and Thrombosis, eds. RW Colman, J Hirsh, VJ Marder and EW Salzman, pp 91-99, J.B. Lippincott Co., Philadelphia PA, USA, 1982.
- Ellis V, Scully M, MacGregor I, Kakkar V; Inhibition of Human Factor Xa by Various Plasma Protease Inhibitors; Biochimica et Biophysica Acta 701, pp 24-31, 1982.
ebiomall.com






>
>
>
>
>
>
>
>
>
>
>
>
1:使用时可按需要的容量加水,以缩短加热的时间。(注意加水不可过多,以免沸腾时水溢出锅外,并注意锅内水量不能低于水箱高度的三分之二,水量过低会造成温冲过高测温不准。长时间使用需经常加水,不能使锅内电热管露出水面。以免烧坏电热管,造成漏水)。接通电源,打开电源开关,指示灯亮.
2. 通电后先闪烁显示dfs,后显示日.以检测数码管笔画是否有缺.
3. 设定温度:按设定键SET设定指示灯SL亮,进入温度设定状态,按上调键▲向上调整0.1℃。按下调键 ▼向下调整0.1℃。再按一次SET键回到测量状态。
4. 调整加热功率系数:长按设置键SET5-8秒,首位显示d.进入设定最低加热功率系数,开机自动为3.可在1-9调整.(使用70-99.9℃时可将加热功率系数调整为5-9即可)。
5. 误差的修正:在确认仪表显示的值不是正确的测量值时可对显示值进行修正。按SET键5-8
秒进入仪表内层菜单,第一个出现的参数为首位显示P.进入设定最低加热功率系数,再按一次SET键出现并的参数C即误差修正参数,配合△或▽键可修改此参数。误差的修正的范围为-9.9℃到+9.9℃,(例如:控温仪显示温度37℃,水箱内的实际温度36℃,则C值减少1℃。 如果控温仪显示温度37℃,水箱内的实际温度38℃,则C值增加1℃。)修正完成后再按一下SET键退出。仪表出厂时C值已修正,使用时要防止把显示正确的仪表修正至不正确。
Hi.baidu/=。www.jingdayq.com。DI展开
实验室自己做滴丸,基质用的PEG4000和PEG6000混合,80℃在水浴锅上熔融,只要基质离开水浴锅就会冷凝,胶头滴管会堵住,滴不出来,是什么原因,怎么解决,各位大神看到帮帮忙

