Formamidinium lead iodide shows a narrower bandgap than the commonly used methylammonium lead iodide (1.48 eV compared to ~1.57 eV), and hence lies closer to that favourable for optimum solar conversion efficiencies. With an approach of FAPbI₃ crystallisation by the direct intramolecular exchange of dimethylsulfoxide (DMSO) molecules intercalated in PbI₂ with formamidinium iodide, device with performance over 20% has been fabricated.

General Information

Product Details

Chemical Structure

Applications

Formamidinium lead iodide shows a narrower bandgap than the commonly used methylammonium lead iodide (1.48 eV compared to ~1.57 eV), and hence lies closer to that favourable for optimum solar conversion efficiencies [1]. Spin-coating the formamidinium iodide (FAI) plus PbI₂ precursor solution in N,N-dimethylformamide (DMF) initially resulted in discontinuous perovskite films. However, by adding a small amount of hydroiodic acid (HI) to the stoichiometric FAI, extremely uniform and continuous films were formed.

Controlled humidity is another deciding factor that affects the film morphology, crystallinity, and optical and electrical properties of FAPbI₃ [2]. 16.6% PCE was achieved with low relative humidity of 2%, with the device efficiency dropped to about half (8.6%) when the humidity was 40%.Low-volatility additives such as FACl and MACl are good candidates for assisting in the crystallisation of phase pure α-FAPbI₃ via the formation of intermediate mixtures, which prohibits the crystallisation of the δ-FAPbI₃ phase [3]. It also has been observed that the black perovskite-type polymorph (α-phase), which is stable at relatively high temperatures (above 160 ^oC), turned into the yellow FAPbI₃ polymorph (δ-phase) in an ambient humid atmosphere. Results show that incorporation of MAPbBr₃ into FAPbI₃ stabilises the perovskite phase of FAPbI₃ and improves the power conversion efficiency of the solar cell to more than 18% under a standard illumination of 100 mW/cm² [4].

With an approach of FAPbI₃ crystallisation by the direct intramolecular exchange of dimethylsulfoxide (DMSO) molecules intercalated in PbI₂ with formamidinium iodide, device with performance over 20% has been fabricated [5].

MSDS Documentation

Formamidinium iodide MSDS sheet

Pricing

Literature and reviews

1. Formamidinium lead trihalide: a broadly tunable perovskite for efficient planar heterojunction solar cells, G. E. Eperon et al., Energy Environ. Sci., 7, 982-988 (2014),  DOI: 10.1039/C3EE43822H. 
2. Controlled Humidity Study on the Formation of Higher Efficiency Formamidinium Lead Triiodide-Based Solar Cells, S. Wozny et al., Chem. Mater., 27 (13), 4814–4820 (2015), DOI: 10.1021/acs.chemmater.5b01691.
3. Additive-Modulated Evolution of HC(NH2)2PbI3 Black Polymorph for Mesoscopic Perovskite Solar Cells, Z. Wang et al., Chem. Mater., 27 (20), 7149–7155 (2015), DOI: 10.1021/acs.chemmater.5b03169.
4. Compositional engineering of perovskite materials for high-performance solar cells, N. Jeon et al., Nature 517, 476–480 (2015), doi:10.1038/nature14133.
5. High-performance photovoltaic perovskite layers fabricated through intramolecular exchange,W-S. Yang et al., Science, 348 (6240), 1234-1237 (2015). DOI: 10.1126/science.aaa9272.
6. Temperature dependence of hole conductor free formamidinium lead iodide perovskite based solar cells, S. Aharon et al., J. Mater. Chem. A., 3, 9171-9178 (2015), DOI: 10.1039/C4TA05149A.
7. High-Efficiency Perovskite Solar Cells Based on the Black Polymorph of HC(NH2)2PbI3, J-W. Lee et al., Adv. Mater., 26: 4991–4998 (2014). doi:10.1002/adma.201401137.
8. Efficient hole-conductor-free, fully printable mesoscopic perovskite solar cells with a broad light harvester NH2CH=NH2PbI3, M. Hu et al., J. Mater. Chem. A, 2, 17115-17121 (2014), DOI: 10.1039/C4TA03741C.

To the best of our knowledge the technical information provided here is accurate. However, Ossila assume no liability for the accuracy of this information. The values provided here are typical at the time of manufacture and may vary over time and from batch to batch.