
Product information | Protocols | References | Technical support | Reviews |
Product overview
Product name | Normetanephrine antibody |
Synonyms | Anti-3-O-Methylnoradrenaline antibody |
Immunogen | Conjugated Normetanephrine |
Specificity | When tested in competitive ELISA, the anti-conjugated Normetanephrineantibody did not show any significant cross reactivity with Normetanephrine analogs, including metanephrine and noradrenaline. |
Volume | 50µL |
Lot number | 140201 |
Storage
Form | Liquid |
Purity | Purified anti-serum |
Storage buffer | Store at +4°C for short term (1-2 weeks). Aliquot and store at -20°C for long term. Avoid repeated freeze / thaw cycles. |
Material safety datasheet | Download MSDS |
Protocols
IF - Cell cultures, Whole mounts, Tissue sections | Dilute antibody with the antibody diluent provided in the STAINperfect immunostaining kit A. Use at 1/250 -1/1000 dilution. Follow the STAINperfect protocol suited to your sample |
Comments | Optimal working dilutions must be determined by the end-user |
Restrictions | For research use only |
Full protocol | Download STAINperfect protocol for Normetanephrine staining |
Protocols-at-a-glance |
![]() | ![]() | ![]() |
Download Normetanephrine staining protocol for tissue sections | Download Normetanephrine staining protocol for whole mounts | Download Normetanephrine staining protocol for cell cultures |
References
TopTechnical SupportSubmit a question
No technical question yet. Be the first to ask!TopReviewsSubmit your review
No reviews yet. Thanks for rating this product.Topebiomall.com






>
>
>
>
>
>
>
>
>
>
>
>
2:冰满探头调整太靠近冰格,顺时针调整180度就好了,也有可能冰满探头坏了。需要更换。
3:水位浮球开关坏,更换。
不过制冰机里的冰不可以,那冰怎么得到呢?
protocol上面说在离心菌液的时候离心管里面要有1/2的冰啊,这个冰应该是碎冰而不是直接冻出来的整块的冰吧。
大家是怎么得到的呢?谢谢!!
⑴开机前必须检查自动供水装置是否正常,水箱存水量是否合理(本机出厂时已调正好水位,用户可不作调正)。
⑵插上电源,制冰机开始工作,首先水泵开始运行(水泵有一个短时间的排空气过程)约2分钟后压缩机开始启动,机器进入制冰状态。
⑶当冰块厚度达到设定的厚度时,冰板探针开始启动,除霜电磁阀开始工作,水泵停止工作,热气进入蒸发器,约1分钟左右冰块下落。在冰块下落时,使落冰档板翻转并打开磁簧开关。当磁簧开关重新闭合时,机器进入再一次制冰过程。
⑷压缩机在整个制冰和脱冰过程中都不停机。
⑸当储冰桶内冰满,磁簧开关不能自动闭合时,机器自动停止工作,当取走足够的冰块,磁簧开关重新闭合后,延时3分钟后机器启动,重新进入制冰过程。
2、冰桥厚度的调正
⑴冰桥的厚度应为3mm左右,探针与蒸发器的间际应比实际的冰桥厚度厚1.5mm左右,顺时针旋转调节螺钉口增加冰桥厚度(螺钉旋转1/3圈冰桥厚度改变1.5mm)。
⑵检查冰板探针的接线和连接支架,应保证自由转动使每个制冰过程后都能回到正确的位置。向左转|向右转

